SPE-1000P4-Port PoE with 5-Port 10/100BASE T Switch ?FCC Warning: This devices has been tested and found to comply with the regulations for Class B digital equipment.pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection againstharmful interference when the equipment is operated in a commercial environment. This equipmentgenerates, uses, and can radiate radio frequency energy and, if not installed and used in accordancewith users guide, may cause harmful interference to radio communications, Operation of this devicesin a residential area is likely to cause harmful interference, in which case the user will be requiredto correct the interference at his/her own expense. ?CE Mark Warning: This is a Class B product. In a domestic environment, this product may cause radio interference, inwhich case the user may be required to take adequate measures. ?UL Warning:1> Elevated Operating Ambient Temperature- If installed in a closed or multi-unit rack assembly, theoperating ambient temperature of the rack environment may be greater then room ambient. Therefore,Consideration should be given to installing the equipment in an environment compatible withmanufacturer’s maximum rated ambient temperature2> Reduced Air flow-installation of equipment in a rack should be such that the amount of air flowrequired for safe operation of the equipment is not compromised.3> Mechanical Loading- mounting of the equipment in the rack should be such as that a hazardousConditions is not achieved due to uneven mechanical loading. Introduction TheC.H.S SPE-1000P/PH Power Source Switch combines a small-high efficiency 5-port10/100BASE-T switch with a standard 802.3af 4-port Power over Ethernet (PoE) capability. TheSPE-1000MB/Mbps incorporates an external - 48VDC power adaptor. Each of the four PoEEthernet ports can provide 15.4 Watts of power as well as 10/100M data transmission over the Inter -connecting Ethernet interface such as Cat 5/ 5e /6 cables. The SPE-1000P/PH switch is a Power Source Equipment (PSE) and fully compatible with Powered Devices (PD) that comply with the IEEE 802.3af PoE standard. The SPE-1000P/PH enables users to attach IEEE802.3af compliant devices such as wireless Access Points (APS), VOIP phone, IP camera, printer and Network Attached Storage (NAS) directlyto the SPE-1000P/PH without requiring additional power on the network . The unit was designed with home and small business users in mind and is ideal for installations where AC power is not available or no cost-effective. No configuration is required and installation is quick and easy. Support for Auto – MDI / MDI-X on allof the ports eliminates the need for crossover connection to another switch or HUB. Auto-Negotiationon each port senses the link speed of a network device( either 10 or 100) and intelligently adjusts forcompatibility and optimal performance. *1-Year Limited Warranty for switch and 1-Year Limited Warranty for the power adaptor are available only in USA and CANADA.* This device is designed for indoor use. Do not use outdoors.* included are the installation manual and the -48VDC power adaptor. Power over Ethernet (PoE) & Features ?Power Over Ethernet (PoE):Power over Ethernet (PoE) integrates 48V power and data onto one single cable, eliminating theneed to have AC power available at all equipment locations.Power and Data are integrated onto the same cable, supporting category 5/5e up to 100 Meters.PoE provides power to PoE compatible devices, such as VOIP telephones, wireless LAN access points,and IP security cameras.PoE devices are readily in the market, saving up to 50% of overall installation cost byeliminating the need to install separate electrical wiring and power outlets. ?Features:l *5 x 10/100Mbps Auto-negotiation Fast Ethernet RJ-45 ports with 4-Port PoE function ( port 1 ~ port 4)l *Compliant with IEEE 802.3af specification.l *Supports PoE power up to 56W for all PoE ports.l *Supports PoE IEEE802.3af compliant Powered Device (PD)l *Each port supports auto MDI/MDIX, so there is no need to use cross-over cables.l *Full/half duplex transfer mode for each port.l *Wire speed reception and transmission.l *Up to 1K unicast address entities per device. Self-learning, and table aging.l *64KBytes packet buffer. Connecting Network Cables ?Connecting Network Cables The SPE-1000P/PH supports five 10/100Mbps Ethernet ports. Port 1 to Port 4 are PoE enabled ports. Each port incorporates 10/100Mbps support via UTP Cat5/5e cables. The four PoE ports will automatically activate when a compatible device is identified. The SPE-1000P /PH will supply power through the Ethernet port to the connected PoE device (PD) Legacy devices that are not compatible will not be supplied power This feature allows users to freelyand safely mix legacy and Power over Ethernet compatible devices on a single network. This Switch supports 10Mbps Ethernet or 100Mbps Fast Ethernet and runs both in half and full duplex mode using two pairs of Category 5 or 5e cable. All ports are Auto-MDI type port. The switch can auto negotiate to MDII or MDI-X type, so you can connect RJ-45 cable regardless of whether it is a standard or crossover cable. Description ?Rear Panel: This is back panel of the SPE-1000P/PH. five RJ-45 ports and one DC power jack. ?Up-Link Link to another Router or Switch. ? Port 1: Standard 10/100Mbps Ethernet port. The Switch supports 10Mbps Ethernet or 100Mbps Fast Ethernet and runs both in half and full duplex mode using two pairs of Category 5 or 5e cable. ? Port 2X to Port 4X: All are 10/100Mbps switch ports as well as 802.3af PoE enabled ports. All PoE port will automatically activate when a compatible terminal is identified. The SPE-1000P/PH will supply power through the Ethernet port to the connected PoE device (PD). The SPE-1000P/PH also supports legacy devices that are not compatible. In this case the PoE port will not supply power to those devices. This feature allows users to freely and safely mix legacy and Power over Ethernet compatible devices on the same network. These RJ-45 ports are Auto-MDI type port. This switch can auto negotiate to MDII or MDI-X type, so you can connect the RJ-45 cable regardless of whether it is a standard or crossover cable. ?DC Power Jack: This DC power jack is located in rear panel left side of the SPE-1000P/PH. Use only the supplied AC/DC adaptor. The use of any incompatible adaptor may causedamage to the equipment and void the warranty. This SPE-1000P/PH does not include a power switch, plugging its power adaptor into a power outlet will immediately power it on.
| 批发说明 |
|---|
|
了解批发详情请 联系卖家 |
| 运费说明 |
|---|
|
了解运费详情请 联系卖家 |
咨询服务专员
放大图片
